Thumbnails with Descriptions

 
Thumb and Description for Image 1:
This gallery shows how the steel wire for the aileron/yoke linkage gets attached to the pulleys.
It shows all the parts that we use in the upper part of the control column where the yoke is attached to.
This first picture was taken before dismantling
 
Thumb and Description for Image 2:
from the side
 
Thumb and Description for Image 3:
the angled part is a 85 degree PVC water pipe angle piece.
 
Thumb and Description for Image 4:
from the back. As you can see, this is the captains yoke, since the AP disconnect pushbutton is on the lefthand side (when seen from the front, of course)
 
Thumb and Description for Image 5:
with the yoke flat on ground: looking inside the pipe piece
 
Thumb and Description for Image 6:
angular piece turned aside
 
Thumb and Description for Image 7:
with the yoke removed: the two metal pieces (the plus-shaped upper one and the one looking out the bottom) are what's called "Lochblech" in German, sheet metal with holes which you can get at any home improvement store around here in many forms and sizes.
 
Thumb and Description for Image 8:
the back of the yoke. doesn't really look nice...
I tried to drill some holes halfway into the wood piece in a half circle kinda shape for the cable (trim, AP disconnect, PTT) to run in when the yoke is turned.
 
Thumb and Description for Image 9:
the angular piece, flat on the floor. the yoke axis is a M10 threaded rod
here you can see the plus-shaped metal piece is held in place by one screw on the bottom (and, not visible in this pic, another one on the top
 
Thumb and Description for Image 10:
here the screw on top can be seen as well as another one (lower part of the picture) that holds the other piece of metal
 
Thumb and Description for Image 11:
looking inside the bottom part...
 
Thumb and Description for Image 12:
closeup of the yoke axis and the plus-shaped metal piece (cut with an angle grinder [german=Winkelschleifer/Flex])
 
Thumb and Description for Image 13:
the plus-shaped part taken out
 
Thumb and Description for Image 14:
looking inside from the front, you can see the pulley where the steel wire linkage will run over
 
Thumb and Description for Image 15:
from the bottom, the pulley again
 
Thumb and Description for Image 16:
how the metal piece is attached from the inside
 
Thumb and Description for Image 17:
from the front with the threaded rod with the pulley taken out
 
Thumb and Description for Image 18:
the pieces (without the nuts) as they were assembled inside the angular pipe piece
 
Thumb and Description for Image 19:
from another angle.
 
Thumb and Description for Image 20:
yet another angle. this should give you an idea how the long metal piece is formed
 
Thumb and Description for Image 21:
the upper end of the long metal piece is formed like a hook.
there's a hole on the end of the hook where the metal piece is attached to the PVC as seen in previous pictures
 
Thumb and Description for Image 22:
adding the steel wires
 
Thumb and Description for Image 23:
again
 
Thumb and Description for Image 24:
the long piece of metal put in place again, now adding the pulley with the steel wires attached
Note: the pulley sits VERY tight on the treaded rod. moving it by hand is nearly impossible.
 
Thumb and Description for Image 25:
another angle
 
Thumb and Description for Image 26:
screwing the yoke back on the axis
 
Thumb and Description for Image 27:
from the front.
 
Thumb and Description for Image 28:
the bottom of the angular piece, with the steel wires and the cable for the buttons coming out
 
Thumb and Description for Image 29:
better lighting
 
Thumb and Description for Image 30:
and a closup.
Generated by mkwebgallery.sh version 0.1.5